6 OUTPUT DTMF DECODER

Control 6 independant outputs using DTMF tones

Selectable 4 digit security code to prevent unauthorised  operation

Optional Morse transpond gives feedback that command has been actioned

Selectable Serial (RS232 compatible) output

£15.99

Our DTMF Decoder kit has 6 NPN open collector Darlington outputs that you can switch on/off, pulse or toggle remotely with or without a 4 digit security code.

TX keying output to key a transmitter for transponding a Morse confirmation. You also have an Audio output for the Morse audio tones.

The PCB has been designed to allow 3 input configurations: unbalanced audio, an Electret microphone or balance audio to be connected. The built version has the unbalanced input configuration.

You can also use it as a DTMF to PC interface allowing DTMF tones to be displayed in, for example, HyperTerminal (see below).

OUTPUTS

It’s easy to turn an output on/off by sending the decoder its ID followed by the output number and * for ON or # for OFF. For example 12341* turns on output 1 and 12342# turns off output 2 and so on.

You can also toggle an output by sending 12341A for example, and the state of the output will be changed to the opposite of its previous state. The Morse transpond will be confirmation of the new state. If you want to pulse an output just send 12341B for example and the output will turn on for 0.5 seconds – the Morse transpond will be say 1P.

PLUS on the latest firmware, you can now use 9 for A and 8 for B so 12 key pads can be used. See the kit in action in this video:

MORSE

When you want confirmation of the desired switching of an output the decoder will key a Transmitter and respond in Morse code; turning on output 1 will respond as 1 ON in Morse, and turning off output 2 will respond as 2 OFF. Simple.

And as there are only 6 digits and 3 letters to learn, there’s no need to let Morse put you off. There is a 2 second transpond delay followed by a 400ms link establishment delay to allow for CTCSS (if used).

Sending the turn off code for the dummy output zero e.g. 12340# will transpond _._._ OFF but won’t affect any outputs. This is useful for checking if in radio range.

DTMF TO SERIAL

If you want to use the kit for DTMF to serial, program the ID as 2320 and next time it’s switched on decoded DTMF tones will be output as RS232 (4800 baud 8N1) compatible serial on the TX keying output; fit the pull-up resistor R12 for this use.

The PCB is a high quality double sided PTH (plated through hole) 1.6mm FR4 (Fiberglass) board 64 x 38mm in size.

A 4 pin programming header is also provided to allow in-circuit re-programming of the PIC.

TURN OFF THE MORSE TRANSPOND

When setting the 4 digit identity add a fifth digit as 9 and the Morse transpond will be turned off. Any other character in the fifth position turns the morse transpond on. When supplied the identity is supplied as 1234 and the fifth digit is set as 0.

You do not need to program the fifth digit if transpond is desired; the fifth digit is not used as part of the identity.

WHAT’S IN THE BOX?

A compact Gold Plated PCB, components and programmed PIC. See the PDF for instruction details and component list.

CHANGE THE 4 DIGIT SECURITY ID

Simply fit a jumper to CN7, turn on the decoder and send it a new 4 digit ID with DTMF. Then turn it off, remove the jumper and switch on again. The new ID is set. If you do not require an ID then simply program the ID as 0000 and on next power-up no ID will be needed and e.g. 1* will turn on output 1.

VIDEOS

DOWNLOADS

 Download DTMF Decoder Kit PDF

 

pdf_symbol[1]Laden Sie DTMF Decoder Bausatz PDF

 

pdf_symbol[1]HT9170 datasheet

 

pdf_symbol[1]Amateur Radio TNC connector to DTMF wiring information

SKU: N/A Category: Tags: ,